1973 Triumph TR6 Complete Restoration
1973 Triumph TR-6
Technical specifications of Triumph TR-6 1973 | |
---|---|
Price: | US $34,000.00 |
Condition: | Used |
Item location: | Arcadia, California, United States |
Make: | Triumph |
Model: | TR-6 |
Type: | Convertible |
Year: | 1973 |
Mileage: | 7,736 |
Color: | White |
Engine size: | 2.5L 6 Cyl |
Number of cylinders: | 6 |
Fuel: | Gasoline |
Transmission: | Manual |
Drive type: | RWD |
Interior color: | Red |
Drive side: | Left-hand drive |
Vehicle Title: | Clear |
You are interested? | Contact the seller! |
Car description |
---|
If you have any questions about this car please contact me at 626.733.7300 or through this ad. This car was completely build from the ground up. I have turned every nut and bolt on this car and it will drive anywhere. I can assist with pickup or shipping the car if you need. Let me know! Thanks for looking.
Over 230 pictures of this car can be viewed from the link below as well as video of the car running.
https://drive.google.com/open?id=100ARjr_B6V7wCV3WXgbkTHy0PugECDqt
This car has 7k miles since a complete rebuild to better than stock, it is ready to drive. The drive train and suspension have been tuned to achieve a higher level of handling and acceleration while keeping the original intent of the chassis. This car has all of the modifications you want and the originality it deserves. Starts every time, would make a great collector or driver. Is an original California car, with a very nice frame, no visible rust. Underside of car is very clean and has been completely restored with a powder coat black. Suspension is very responsive and is a match for most street cars in the corners. I’ve been restoring and rebuilding car since 1979 as a mechanical engineer. I can maintain the car for you if you live in the Los Angeles area, my rates have no overhead added.
Engine
6 Cylinder 2.5L engine only 7k on Pro-rebuild balanced, line honed.
Weber Triple Carburetors, intake with balance tube.
Stainless Phoenix header and exhaust
Phoenix dual box exhaust
Wishbone classics 518 V2 camshaft, toolsteel tappets and 6500RPM springs and stainless gas flow valves.
Accusump oil accumulator, good for long term storage / pre-oiling
Mocal spin-on filter.
MSD Ignition w/ dash timing control, 6AL with dial rev-limiter
Wizard cooling aluminum radiator (USA) w/ electric auxiliary thermostatic fan, Goodparts shroud
Goodparts roller rockers w/ cylinder ported and flow benched includes wishbone classics guides, seats, seals, keepers, Payen gaskets
Chromoly tubular pushrods
Drivetrain
Rebuild transmission with overdrive
Goodparts rear axle conversion and drive shaft
Goodparts CV joints
New motor, transmission, and diff mounts
Suspension
Goodparts adjustable anti-roll bars Front/Rear
Brake and clutch master cylinder recently replaced
Goodparts nylatron bushings Front/Rear
KYB gas shocks rear
KYB gas Front shocks
Goodparts adjustable semi trailing arm brackets
TRW Brake pads
New Brake vacuum booster
Goodparts/Roadster factory front axle with Timken bearings and bearing spacers (Axle strength)
Goodparts springs
Goodparts solid rack mounts and new rack
Exterior
White lacquer paint
All rubber replaced
Original Factory Hard Top w/ New Roadster Factory bone headliner, all new seals
Soft top w/ Roadster Factory stafast fabric wine berry with reflector stripes, all new seals
Moss Motors Front spoiler
17” ROTA wheels with proper offset
Hankook Venus V12 EVO 215/50R17 Tires
Custom Black-yellow CA plates
Interior
Red interior
Walnut Burl Veneer dash
RetroSound radio Model 2
A/F ratio gauge, Innovate motorsports
Roadster Factory panels w/ new fasteners installed correctly, glued as per factory, snaps as per factory
Roadster Factory Wilton wool carpet
Roadster Factory seat upholstery w/ new foam
Roadster Factory trunk panels and carpet with restoration
Original TR6 handbook
I am selling because I enjoy building cars and I’m ready to fund another project. Check the websites/companies listed, this work can’t be done for double the asking price excluding labor. A stock rebuild of a TR6 engine with quality parts and cam is 10k alone.