NO RES! NICE 1986 Suzuki Samurai fuel injected 1.6L 16v engine Warn winch Garvin

This is a beautiful Suzuki Samurai! I purchasedthis extremely clean, all original, 1986 Samurai in September 2014. It was garaged it's whole life, as can be seen by the original paint. I would love to take credit for the virtually spotless engine compartment, but it was that way when I bought it (I just maintained). I am very picky, so was looking for a cherry Samurai, and I found it in this one!. My original intention was a hunting and trail rig, and I passed up many used/ abused, and trashed Sammi's. I removed the perfect condition carpet kit, to witness beautiful bright red paint underneath. There is no rust on this rig, period! I wanted to apply bed-liner to the tub, so I could just spray it out when it gets muddy inside, and that's also why I went with a Kenwood Marine KMR-M315BT radio (Ipod in pics not included). I left the center tunnel area the original bright red paint, as a reminder of a 77 Ford I had back in the day. There are no cracks in dash or head-rests. I then realized it had no ground clearance with thetiny 26" tires, and anemic with the carbed 1.3 engine....and so it began....

Suspension- I wanted a low center of gravity, so I went with a 2.5" suspension lift via Old Man Emu spring lift(much softer than stock)...I also installed a 1" body lift, but this was only done to clear a tallerengine that is about twice the horsepower! So 3.5" lift total.

Tires- I wanted 31"x10.50x15 tires, so I went with Pro-Comp Xterrain mud tires (also fine on highway). I used a nice BFG All Terrain31" as a spare.

Engine- I had a 1995 Geo Tracker Fuel Injected 1.6 Liter, 16v engine completely overhauled and bored .020 overby Aims Inc. Sparks, NV. (receipt will be provided). This was completed on 7/8/2015, and has about 3000 miles total on this new engine.Please note that this is a professional installation. It involved fully removing Samurai wiring harness & computer, for reliability. Sub-standard swaps will "vampire" into the original harness. Nothing on this buildis sub-standard! Also installed is a Calmini stainless steel header for more HP, as if twice the power of original is not enough....Reno has smog requirements, so all sensors are functional, and this rig passes smog with flying colors! For cooling I installed an aluminum radiator, which has no problems in the Nevada desert, and red silicone hoses.

Gauges- I invested over 3k into the engine, so monitoring is critical! I removed the top three vents, and installed gauges for water temp, oil pressure, and voltage. This is a perfect install, that looks stock, with absolutely no cutting involved!

Heater- You were wondering because the three vents removed, right? Nope, heater and defroster works AMAZING!!! (Reno gets to -0, and there are no problems!)

Exhaust- Custom exhaust ran "high and tight" (receipt will be provided), exiting through a Thrush Turbo muffler (receipt will be provided).

Steering- I installed a Roadless Gear rag joint eliminator, for more positive steering control. I decided against power steering, because it is easy to steer (IMO), and I didn't want to rob any HP.

4x4 stuff- I had Lowrange Offroad 4.9:1 gears installed in the transfer case. This makes it amazing offroad in 4x4! It will crawl no problem. I actually wish I would have kept the stock gearing, because most of my miles have been highway. This engine will easily do 70mph, and the t-case is the limiting factor at 3/4 throttle. I also went with Lowrange Heavy Duty transfer case mounts & heavy duty bushings. Has rock sliders installed as well, in case you want to use them.

Recovery- I purchased a custom made bumper (awesome), and mounted a Warn M8000 winch, with Smittybilt 8000lbs synthetic winch line, & aluminum fairlead (zero pulls to date).

Yes, all lights and signals work....

Other Awesome Stuff- The soft-top is in perfect shape, but also has a perfect bikini top. Has a 15 gallon Petroworks fuel tank, with internal fuel pump, a Garvin Wilderness Heavy Duty safari rack in case you want to carry several hundred extra pounds, Tuffy locking security console with 2 drink holders. Has new heavy duty U-joints installed.

Cons- Wow, this is tough because I'm more critical than most people....There is a chip in the windshield that I would get fixed. I had to remove the windshield reservoir tank to make the 1.6L air-cleaner look stock. There is a hole in the rear area, under rear seat, that I drilled to tighten the Petroworks fuel tanks wiring (I failed to check before mounting the tank...ugh). This can be drilled, and a body plug installed...There is no jack/ handle, because I just put my nice aluminum floor jack inside...Missing door handle on inside, and the "bucket" of the latch is broken. Although it opens and closes perfect, I was going to buy aftermarket aluminum. The biggest problem I have with it is the seats. They are comfortable to me, but I know they need re-upholstered. The awesome seat covers are hiding the defects, but they are there...

Why isn't this pictured on rocks, or covered in mud? Because it's NEVER been in a mud pit, or in the rocks!!! I seriously mean NEVER!! I don't abuse my vehicles, PERIOD! If you want to abuse this, that is on you my friend. This turned out so amazing, Ihave only beentaking it cruising for yard sales, or commuting to work, and it gets compliments everywhere I go....That is why I'm selling....This is too nice for me to hunt and trail-ride in, so I am going to get a beater or side x side...This rig is just too nice for me, because I catch myselfnot wanting to get it scratched etc.Please note, I have removed the 775 sticker from windshield...

A deposit of $500 is required within 24hrs of auction end, and the buyer will be responsible for ALL shipping charges, and arrangements. The remaining balance should be paid by cash or USPS Money Order, within 7 days of auction end. I will happily drive to anywhere in the Reno area...Someone will ask "can I drive this to Maine"? I would answer sure, if you have the time! The longest road-trip I made was about 500 miles, and that wasn't a problem. As stated earlier, it will easily do 65-70, but the transfer case gearingis the limiting factor to going faster.

I am located in Sparks, NV. 89434 (Reno area), You are absolutely welcome and encouraged to call me at (775) 378-0579 with any and all questions you may have. I can also e-mail additional pics of when I first got it, video etc. Of course anyone is welcomed to inspect it in person, go for a ride etc. It is your hard earned money, and I want you to be assured this rig is nice!