1968 Mustang GT Fastback S Code 4 Speed

This is a 1968 Mustang Factory GT 390 4-speed Fastback. It is a true ‘S’ code car. The car has been completely restored from top to bottom. Every bolt and nut was removed, body was installed in a rotisserie and sandblasted to determine the extent of any rust. It was then leveled and secured so all rusted parts could be cut out and replaced. Multiple measurements were recorded using a trammel beam to insure proper fit of new sheet metal. Both rear frame rails were repaired, new trunk drops, rear trunk crossmember, new taillight panel, new full left Dynacorn quarter panel, new Dynacorn roof panel, repair panel on right side quarter, new Dynacorn doors on both sides. Both full floor pans along with toe boards and both torque boxes were replaced. Body was reinstalled in a rotisserie and completely painted with 3 coats of Black Epoxy Primer. Underside was then painted with PPG’s Black Chassis Paint.Engine is a 390 date code correct block, bored .060, forged pistons, crank turned .010/.010, comp cams mother thumper with spring/retainers/lifter kit, original GT date correct heads completely redone with new valve seats and new valves. Edelbrock intake, holley 750 double pumper carb, JBA tri-Y ceramic coated headers, high torque starter and Flowmaster exhaust kit. Engine idles at 1200 RPM’, cam comes in at about 2200 RPM’s and pulls VERY strong from there up. This is not a mild engine.Transmission is correct Ford toploader 4-speed with VIN stamped on front case. Was originally a wide ratio, now converted to close ratio gear set. Factory correct Ford shifter. New driveshaft complete with U joints.9” rear-end was completely disassembled, new 4.11 ring and pinion, new posi-traction clutch pack, all new bearings including axle bearings, new axle lug studs. Housing was replaced with a 1957 Ford Station Wagon housing to allow clearance for rear tires.Wheels are Foose Aluminum Chrome plated (not polished) 17” front and back.Car has factory A/C, power disc brakes, power steering, factory Ford tilt-away steering wheel, factory tach dash. The A/C system was pumped down but not charged. Compressor oil is only compatible with R-12 Freon. It will need to be flushed if R-134 is preferred.Interior has been completely redone with all new upholstery, carpeting, headliner, door panels, Zuma AM/FM radio with USB, Pioneer Kick Panel speakers. Factory fold down rear seat.Front suspension is completely new, upper and lower control arms, 1” lowered coil springs, larger sway bar with new bushings, new front wheel bearings and seals, all new brake lines, hoses and gas lines. New rear 1” lower leaf springs with 1” lowering blocks, all new shocks. New gas tank and sending unit.Paint is Spies Hecker 2015 Mercedes Benz Palladium Silver Basecoat/Clearcoat. All body parts were painted with Epoxy primer, then 2K primer before finish was applied. Stripes are 3M vinyl and could be removed.I personally restored this car. I have been retired for many years and do one car at a time. I’ve done 68, 69 and 70 mustangs and an occasional 57 ford. This is one of my favorites. It truly gets a ton of attention wherever I drive it. I have had the car done for approximately 2 years and am now working on a new project so it’s time for this one to go. Whoever buys this car will not be disappointed, there’s really nothing it needs short of tuning the distributor timing range. It really doesn’t have enough range on the advance side. Someone with distributor knowledge could respring the advance correctly and it would probably perform even better than it does now.I am asking for a $500 deposit within 24 hours of purchase using paypal. The balance can be a wire transfer or cash is always welcome. The car will not be released until all funds are in my possession. Any shipping should be handled by the buyer at buyer’s expense. I will be more than happy to help get it loaded. There is a large shopping area right off the interstate for loading onto a transport truck or there’s always room to load it onto your trailer right here at my place. The car is being sold as is where is with no warranties written or implied. Please ask any questions you may have, I’ll do my best to answer, and thanks for looking.Just realized I changed out the stock oil pan with a Moroso 7 qt. since the pictures were taken. I also replaced the stock distributor with a pertronix billet flame thrower along with the corresponding coil. Sorry for any confusion.